BEC 7800 Instrukcja Użytkownika

BEC 7800 Dual WAN ADSL2+ Firewall Router User Manual Version rekease 1.01

7 The Rear Ports Port Meaning 1 Power Switch Power ON/OFF switch. 2 Power Connect it with the supplied power adapter. 3 RESET Press more t

8 Cabling One of the most common causes of problem is bad cabling or ADSL line(s). Make sure that all connected devices are turne

9 Chapter 3: Basic Installation The router can be configured through your web browser. A web browser is included as a standard app

10 Connecting Your Router Users will not be able to connect to the internet through EWAN if DSL is already connected to the inte

11 Network Configuration Configuring PC in Windows Vista 1. Go to Start. Click on Network. 2. Then click on Network and Sharing Center at th

12 5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties

13 Configuring PC in Windows XP 1. Go to Start > Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2.

14 Configuring PC in Windows 2000 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and Dia

15 Configuring PC in Windows 95/98/Me 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and

16 Configuring PC in Windows NT4.0 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and cho

Table of Contents Chapter 1: Introduction ... 1 Introduction to your Router ..

17 Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface (Username and Passwo

18 Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out what kind of

19 Chapter 4: Configuration Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a logi

20 Quick Start Step 1: Select WAN port connect mode from the connect mode drop down menu. There are two types of connect mode to choose from: ADS

21 Step 3: After finishing configuring the WAN connection, press Continue to finish the QuickStart. At this time, you will see the system rebootin

22 PPPoA VPI/VCI: Enter the information provided by your ISP. Username: Enter the username provided by your ISP. You can input up to 256 alpha

23 IPoA Connection VPI/VCI: Enter the VPI and VCI information provided by your ISP. Encapsulation mode: Select the encapsulation format. Select

24 MPoA Connection VPI/VCI: Enter the VPI and VCI information provided by your ISP. Encapsulation mode: Select the encapsulation format. Select

25 EWAN Connect Mode For EWAN connect mode there are 2 types of connection protocols: PPPoE and IPoW. PPPoE connection Username: Enter the

26 IPoW connection IP Address: Your WAN IP address. Leave the IP address as 0.0.0.0 to enable the device to automatically obtain an IP address f

IP Alias... 39 DHCP Server ...

27 Status (Basic Mode)

28 Cofiguration (Basic Mode) A WAN (Wide Area Network) is an outside connection to another network or the Internet. There are two items within the

29 PPPoA Connection (ADSL) PPPoA stands for Point to Point Protocol over ATM Adaptation Layer 5 (AAL5). It provides access control and billing fun

30 MPoA Connection (ADSL) VPI/VCI: Enter the VPI and VCI information provided by your ISP. Encap. mode: Select the encapsulation format. Select

31 IPoA Connections (ADSL) VPI/VCI: Enter the VPI and VCI information provided by your ISP. Encap. mode: Select the encapsulation format. Sele

32 Pure Bridge Connections (ADSL) VPI/VCI: Enter the VPI and VCI information provided by your ISP. Encap. mode: Select the encapsulation form

33 WAN Profile – Main Port (EWAN) Besides using ADSL to get connected to the Internet, Ethernet port 1 of BEC 7800 can be used as an althernative

34 IPoW (IP over Ethernet) IP Address: Your WAN IP address. Leave the IP address as 0.0.0.0 to enable the device to automatically obtain an IP a

35 Status (Advanced Mode)

36 ADSL DSP Firmware Version: DSP code version. DMT Status: Current DMT Status. Operational Mode: Display the ADSL state when the connect mode

1 Chapter 1: Introduction Introduction to your Router Thank you for purchasing BEC 7800 Router. Your new router is an all-in-one unit that combine

37 ARP This table shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful in determining the MAC address of the

38 System Log Display all the system logs that have been recorded up to the present time.

39 Configuration (Advanced Mode) LAN A Local Area Network (LAN) is a shared communication system network where many computers are connected. Thi

40 DHCP Server DHCP allows networked devices to obtain information on the parameter of IP, Netmask, Gateway as well as DNS through the Ethernet

41 WAN A WAN (Wide Area Network) is a computer network that covers a broad geographical area (eg. Internet) that is used to connect LAN an

42 Auth. Protocol: Default is Auto. Please consult your ISP on whether to use Chap, Pap or MSCHAP. Connection: Always on: If you want the rou

43 PPPoA Connection (ADSL) PPPoA stands for Point to Point Protocol over ATM Adaptation Layer 5 (AAL5). It provides access control and billing fun

44 MPoA Connection (ADSL) Description: A user-definable name for this connection. VPI/VCI: Enter the VPI and VCI information provided by your I

45 IPoA Connections (ADSL) Description: A user-definable name for this connection. VPI/VCI: Enter the VPI and VCI information provided by your

46 Pure Bridge Connections (ADSL) Description: A user-definable name for this connection. VPI/VCI: Enter the VPI and VCI information provided

2 Features Express Internet Access The router complies with ADSL worldwide standards. It supports downstream rate up to 12/24 M

47 WAN Profile – Main Port (EWAN) Besides using ADSL to connect to the Internet, BEC 7800 Ethernet port 1 is also an alternative to connect to Cab

48 specified by your service provider when this information is required. The default setting is set to disable. MTU: Control the maximum Ethernet

49 ADSL Mode ADSL Mode: There are 2 modes “Annex L” and ”Annex M” that user can select for this connection. Modulator: There are 5 modes “ADSL

50 System There are five items within the System section: Time Zone, Firmware Upgrade, Backup/ Restore, Restart and User Management. Time Zone

51 Backup / Restore These functions allow you to save a backup of the current configuration of your router to a defined location on your PC, or

52 Restart There are 2 options for you to choose from before restarting the your 7800 device. You can either choose to restart your device to re

53 Firewall Packet Filter Packet filtering enables you to configure your router to block specified internal/external users (IP address) from Int

54 Edit: Check the Rule No. you wish to edit, and then click “Edit”. Delete: Check the Rule No. you wish to delete, and then click “Delete”. MAC

55 Virtual Server Virtual Server allows you to direct incoming traffic from WAN side (identified by Protocol and External port) to the Internal se

56 Port Mapping Application: Select the service you wish to configure. Protocol: A protocol is automatically applied when an Application is sel

3 Allows multi-users to access outside resources such as the Internet simultaneously with one IP address/one Internet access account.

57 DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packe

58 Advanced Static Route Enter the destination network address, subnet mask, gateway AND/OR the available WAN interface, then click “Add” to a

59 VLAN VLAN (Virtual Local Area Network) is a group of devices on different physical LAN segments that can communicate with each other as if they

60 Device Management The Device Management advanced configuration settings allow you to control your router’s security options and device monitori

61 Installing UPnP in Windows Example Follow the steps below to install the UPnP in Windows Me. Step 1: Click Start and Control Panel. Double-cli

62

63 Step 4: Click OK to go back to the Add/Remove Programs Properties window. Click Next. Step 5: Restart the computer when prompted. Follow th

64 Auto-discover Your UPnP-enabled Network Device Step 1: Click start and Control Panel. Double-click Network Connections. An icon displays u

65 Step 4: You may edit or delete the port mappings or click Add to manually add port mappings. Step 5: Select Show icon in notification ar

66 Step 6: Double-click on the icon to display your current Internet connection status. Web Configurator Easy Access With UPnP, you can ac

4 Chapter 2: Installing the Router Important note for using this router

67 Step 4: An icon describing each UPnP-enabled device shows under Local Network. Step 5: Right-click on the icon of your BEC 7800 and select Invo

68 IGMP IGMP, known as Internet Group Management Protocol, is used to manage hosts from multicast group. IGMP Proxy: Accepting multicast packet

69 Remote Access Remote Access Control: Select Enable to allow management access from remote side (mostly from internet).

70 Appendix: Product Support & Contact If you come across any problems please contact the dealer from where you purchased your prod- uct.

5 Package Contents BEC 7800 Dual WAN ADSL2+ Firewall Router CD containing the online manual RJ-11 ADSL/Telephone cable

6 The Front LEDs. LED Meaning 1 Internet Lit red when WAN port fails to get IP address. Flash green when WAN port gets IP address su